雷诺数对轴流风扇/压气机性能和稳定性的影响

介绍了一种预估轴流风扇／压气机特性和不稳定边界的方法。该方法采用考虑雷诺数影响的“基元叶栅法”计算轴流风扇／压气机特性，并利用C．C．Koch提出的“有效静压升系数法”预估轴流风扇／压气机的不稳定边界。为了验证方法的可行性，本文模拟了从地面到20 000m高空的雷诺数变化，对一个五级高压压气机在不同雷诺数下的特性及稳定性进行了计算分析。计算结果表明，轴流压气机的特性和稳定性都随雷诺数的降低而下降。     

面向绿色制造的高效冷却技术及其试验

绿色制造和高效加工是21世纪先进制造业的必然趋势,为实现绿色高效加工,本文提出了一种新型的绿色高效冷却技术——低温气动喷雾射流冲击冷却技术,通过低温气流运载少量冷却液以喷雾射流冲击的形式到达加工区实现强化换热,将加工区的换热水平提高到一个全新的水平.瞬态实验结果表明,在射流速度40 m/s、靶距10 mm的射流条件下,这种冷却方式可提供的临界热流密度高达60W/mm^2,相对于磨削发生烧伤的临界热流密度提高了6倍以上.     

燃烧室头部进气规律对煤粉燃烧效率的影响

用实验方法研究了火焰筒式煤粉燃烧室头部进气规律对燃烧效率的影响。通过对6种结构的头部配气方案的分析比较,得出了煤粉燃烧室合理的头部配气方案,为今后煤粉燃烧室的设计和工作状态的选择提供了重要的实验依据。     

扰流环对粉末发动机燃烧流动影响的数值模拟

为了提高粉末火箭发动机的燃烧效率,通过数值模拟方法研究了扰流环的有无、通径及位置对燃烧室燃烧流动特性的影响。结果表明:扰流环会增强Al颗粒和气相的掺混和换热程度,促进Al颗粒蒸发和燃烧,从而提高粉末火箭发动机的燃烧效率。当扰流环通径比在0.538~0.846范围内时,扰流环的通径越小,燃烧效率越高;当扰流环头部距离比在0.3~0.8范围内时,扰流环位置离头部越近,燃烧效率越高。设计扰流环时,应在距离燃烧室头部30%~40%的位置布置小通径的扰流环。      

基于压力信号分析的轴流式压气机失速预测

为了得到压气机工作状态的稳定观测点,并建立压气机近喘失速工作状态与压气机压力信号的相关关系,本文针对低速双级轴流式压气机,分别进行了均匀进气及畸变进气条件下不同转速的近喘失速试验,实时动态测量标定压气机由正常工作到失速工况下压力信号,并在时域内提出了一种基于自相关系数的压气机失速预测算法,对进口、出口以及压气机首级转子叶尖位置压力信号预测分析。结果表明所提出的预测算法具有良好的失速预测能力,且发现叶尖处离叶片前缘20%的位置,最适宜作为压气机失速预测的观测点,此时压气机叶尖压力自相关性数据与压气机喘振裕度具有明显的单调相关性。     

一种整体式天然气压缩机气阀故障诊断技术研究CSCD

整体式天然气压缩机在石油化工领域广泛应用,压缩机的正常工作对安全生产具有重要意义。为了有效诊断整体式压缩机气阀部件的故障,采用了Daubechies小波基函数对ZTY470型整体式天然气压缩机气阀振动信号的分解重构原理,详细介绍了以振动信号的能量为故障特征的故障诊断过程。对气阀阀片断裂和弹簧断裂的故障振动信号进行了小波包分析,并与正常工作时的信号进行了对比。实验表明该方法能准确的进行故障诊断和故障定位,证明了对整体式天然气压缩机气阀故障诊断的有效性。     

Effect of protrusion amount on gas ingestion of radial rim seal

In this paper, the effect of different amount of protrusion on various parameters in rotor–stator system was experimentally studied by measuring CO₂ concentration and pressure, in order to obtain the optimal protrusion amount. The parameters of different dimensionless sealing flow were measured under the condition that the annulus Reynolds number was 4.39 × 10⁵ and the rotating Reynolds number was 1.05 × 10⁶. The results show that the change of the amount of protrusions has little effect on the static pressure in the cavity, and the static pressure change near the sealing ring is almost negligible. But the total pressure and sealing efficiency increase first and then decrease with the increase of the amount of protrusion. The variation of power consumption is the same. A complex vortex structure will appear at the high radius region when the protrusion is installed. On the other hand, the protrusion can effectively reduce the minimum sealing flow of the rotor–stator cavity. Furthermore, considering the sealing efficiency and power consumption, the best range of the protrusion amount is about 36. The ratio near this range can optimally balance the alleviation of the gas ingestion and the reduction of the power consumption.     

等离子体助燃下超燃支板燃烧室燃烧特性数值研究

为了将支板喷注器与等离子体射流这两种促进超声速燃烧室燃烧的方式结合起来,设计了一种带有等离子体射流喷孔的支板燃烧室,并在超声速来流的条件下,针对燃料喷注总压、燃料喷注位置、等离子体射流介质、等离子体射流总压对燃烧室燃烧性能的影响进行了三维数值模拟。研究发现:增大燃料的喷注总压,燃烧室的燃烧范围明显增大,燃烧效率呈现出先增大后减小的趋势,在燃料喷注总压为2.0MPa时,燃烧效率达到最大值90.4%;不同的燃料喷注位置对燃烧室的燃烧范围影响较小;等离子体射流介质为O2时,燃烧效率最高,燃烧范围最广;提高等离子体射流的喷注总压,能够提升凹腔剪切层高度,有效促进燃烧,但同时也带来了更高的总压损失。     

改进人工蜂群算法及其轴流压气机优化应用

为了探索更优的全局优化算法并将其应用于轴流压气机气动优化上，将标准人工蜂群（ABC）算法中采蜜蜂和观察蜂探索新蜜源的方式进行改进，从而更好地利用总体蜜源的探索信息，得到改进人工蜂群（IABC）算法。经基准函数测试表明，改进算法既能提升全局寻优能力，又能加快收敛速度。采用IABC算法和经过校核的CFD数值方法搭建优化平台，对单级跨声速轴流压气机Stage35进行优化。优化变量为动叶和静叶径向6个截面的弯、掠、前缘重弯值和尾缘重弯值，以流量和压比相对变化保持在0.5%以内为约束条件，以提高绝热效率为优化目标。结果表明：在设计转速下，优化后设计点绝热效率提升0.83%，全工况范围内平均绝热效率提升2.0%，同时喘振裕度提升1.0%，验证了IABC算法在轴流压气机优化中的有效性。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).